DuraVision FDF2301-3D | EIZO
Technical paper on this monitor's backlight system
From the Journal of the SID (PDF: 2,077 KB)
- Security & Surveillance
- Touch Panel
- Factories & Kiosks
- Awards & Reviews
Glasses-Free 3D Monitor
The DuraVision FDF2301-3D produces stereoscopic (3D) images without glasses. In an industrial or academic environment where the FDF 2301-3D might be used for several hours at a time or in tandem with a 2D monitor, this saves you from having to wear cumbersome 3D glasses.
Parallel Use of a 2D and 3D Monitor with Glasses
Parallel Use of a 2D and 3D Monitor without Glasses
Full High-Definition Display
No Moiré, Stripe Noise, or Pseudoscopic Images
The FDF2301-3D does not produce the moiré or stripe noise often seen with 3D monitors that require glasses. Furthermore, the pseudoscopic images that result when right and left parallax images invert depending on the viewing angle are also not an issue.
Large 23" Screen
With EIZO's patented elliptical mirror technology, the advantages of the directional backlight can be applied to a relatively large screen.
Side by Side
The monitor receives right and left parallax images, splits them into two, doubles their size horizontally, and alternately displays them as right and left parallax images. Because the images are doubled in size horizontally, their horizontal resolution is halved.
3D Image Modes
In addition to a 120 Hz Frame Sequential mode, three other modes are included – Anaglyph, Dual Input, and Side-by-Side.
Right and left parallax images are alternately shown at a frame rate of 120 Hz.
Monochrome images from the left and right eyes are combined as red and blue respectively and transmitted as color signals. The red and blue parts are then separated and converted to monochrome images and allocated as left and right parallax images. Frame rates of up to 60 Hz are supported.
The signals of right and left parallax images are transmitted by different cables. The frequency and resolution of the signals are the same and support refresh rates of up to 60 Hz. When the right and left 3D signals are independent of each other, the two DVI-D 24-pin connectors on the monitor support dual input.
The two DVI-D 24-pin connectors cannot be used for accepting signals from two computers.
DVI-D 24-Pin and VESA Stereo Sync 3-Pin Connectors
One dual link and one single link DVI-D 24-Pin connector are included. In addition, a VESA Stereo Sync 3-pin connector that synchronizes signals so right and left parallax images are displayed properly when outputted from a graphics board that also supports VESA Stereo Sync.
Compliance with Safety and Environmental Standards
The DuraVision FDF2301-3D complies with many international standards includuing RoHS, CB, and the CE Mark.
|Size||23" / 58 cm (584 mm diagonal)|
|Native Resolution||1920 x 1080 (16: 9 aspect ratio)|
|Viewable Image Size (H x V)||509.8 x 286.7 mm|
|Pixel Pitch||0.265 x 0.265 mm|
|Display Colors||2.09 million|
|Contrast Ratio (typical)||1000:1|
|Input Terminals||DVI-D 24 pin x 2, VESA Stereo Sync 3 pin x 1|
|Digital Scanning Frequency (H / V)||
31 - 136 kHz（primary） / Single link: 59 - 61 Hz, Dual link: 119 - 121 Hz
(VGA Text: 69 - 71 Hz) Interlace display not supported.
|Power Requirements||AC 100 - 120 V / 200 - 240 V, 50 / 60 Hz|
|Maximum Power Consumption||105 W|
|Power Save Mode||Less than 8 W|
|Features & Functions|
|Others||3D mode: Side by Side, Anaglyph, Frame Sequential, Dual Input|
|Dimensions (Landscape, W x H x D)||650 x 566.3 x 283.8 mm|
|Net Weight||19.8 kg / 43.7 lbs|
|Height Adjustment Range||-|
|Tilt||10° Up, 5° Down|
|Operating Temperature||0 - 30 °C|
|Operating Humidity (R.H., non condensing)||20 - 80 %|
|Certifications & Standards (Please contact EIZO for the latest information.)||c-Tick, CE, CB, cTUVus, TUV/S, FCC-A, Canadian ICES-003-A, VCCI-A, RoHS, WEEE|
|Supplied Accessories||AC power cord, signal cables, setup guide, warranty card, user's manual|
- 2 With current LCD technology, a panel may contain a limited number of missing or flickering pixels.
5710 Warland Drive, Cypress, California 90630
(+1) 562 431 5011
(+1) 562 431 4811